 |
Project Ideas - Same Day Projects
Trim most rooms in your home in one day using the quick and easy no-miter system from Decra-Mold. No special tools required.
| |
Pick your project:
|
|
|
How To Install
|
| |
- Tools Needed:
- Tape measure, drill (1/16" bit), hammer, adhesive, pencil, sand paper, straight edge, stain or paint, safety glasses, fine tooth saw, level, wood putty, finish nails.
- For Best Results:
- Pre-drill, sand and finish all blocks and wood molding before installing. All blocks should be installed before molding is cut to fit.
|
|
|
| |
|
Step 1: Position blocks as indicated in the descriptions below making sure they are level and plumb. Stabilize the block from movement. Secure blocks in place with glue and finish nails.
|
 |
|
Step 2:
Measure for a snug fit between blocks for length of each piece of moulding. Cut to fit with easy straight cuts.
|
|
Step 3:
Nail each piece of moulding or casing in place starting at one end and working to the other. Make sure to keep moulding or casing as straight as possible. (Base blocks and rosette blocks are sightly wider than most casing. When installing casing, center on the blocks. This will leave a 1/4" reveal on the inside edge of the window or doorway opening.)
|
|
Step 4:
Countersink all nail heads and fill with wood putty. Touch up with paint or stain.
|
Top of Page
|
|
| |
Crown Corner Blocks
|
|
| |
Sizes fit crown mouldings up to 5-1/4"
Outside Crown Corner Blocks - wrap around the outside 90 degree corner of the protruding wall. The top edge of the block should be flush against the ceiling.
Inside Crown Corner Blocks - fit squarely in the inside 90 degree corner of a wall. The top edge of the block should be flush against the ceiling.
Top of Page
|
|
| |
Crown Divider Blocks
|
|
| |
Sizes fit crown mouldings up to 4-3/8"
Crown Divider Blocks - are positioned between two pieces of crown moulding where a ceiling and wall meet with the top of the divider flush against the ceiling.
Top of Page
|
|
| |
Crown Shadow Corners
|
|
| |
Sizes fit crown mouldings #47, #48, #49, & #52
Crown Shadow Corners are larger than standard mouldings to make for easier installation and to create a decorative Shadow Effect!
Outside Corners - wrap around outside 90 degree corner of a wall.
Inside Corners - fit squarely in the inside 90 degree corner of a wall.
Top of Page
|
|
| |
Base Corner Blocks
|
|
| |
Sizes fit base boards up to 5-1/4"
Outside Base Corner Blocks - wrap around the outside 90 degree corner of a protruding wall with the bottom edge flush against the floor surface.
Inside Base Corner Blocks - fit squarely in the inside 90 degree corner of a wall with the bottom edge flush against the floor surface.
Top of Page
|
|
| |
Chair Rail Corner Blocks
|
|
| |
Fits chair rail moulding up to 3-1/4"
Mark level line around perimeter of room at the desired height using a level or chalk line.
Outside Chair Rail Corner Blocks - wrap around the outside 90 degree corner of a protruding wall.
Inside Chair Rail Corner Blocks - fit squarely in the inside 90 degree corner of a wall.
Top of Page
|
|
| |
Casing Base Blocks
|
|
| |
Available in sizes from 2-3/4" X 4" to 5-1/2" 8"
Casing Base Blocks - place blocks at the bottom of the doorway flush with the door jamb and flat on the floor surface.
Top of Page
|
|
| |
Casing Rosette Blocks
|
|
| |
Available in sizes from 2-1/2" to 5-1/2"
Casing Rosette Blocks can be used on all four corners of a window or on just the top two corners of a window or door. Position rosettes so that the corner of the rosette just touches the corner of the window or door.
Top of Page
|
|
|
|
